lexa345 发表于 2013-8-6 16:56:31

Siemens 840D - 3 AXIS VMC MILL FOR X6



; TOOL - 237 DIA. OFF. - 237 LENGTH - 237 DIA. - 3 MM - POCKET
T="3. BALL ENDMILL"
M6
G0 G17 G54 G90 G94
M3 S4000 F369.23
G00 X-19.567 Y14.098
Z0.
G1 Z-4. F300.
......
.......
Y16.593
X-18.553 Y-.02
G41 D237 X-15.589 Y12.593
Y15.593
G3 X-18.589 Y18.593 CR=3.
G1 X-21.589
G3 X-23.589 Y16.593 CR=2.
G1 Y-16.407
G3 X-21.589 Y-18.407 CR=2.
G1 X-15.589
G3 X-13.589 Y-16.407 CR=2.
G1 Y16.593
G3 X-15.589 Y18.593 CR=2.
G1 X-18.589
X-18.889
G3 X-21.889 Y15.593 CR=3.
G1 Y12.593
G40 X-18.553 Y-.02
G0 Z0.
M5
G0 G90 G53 D0 Z0
; TOOL - 47 DIA. OFF. - 47 LENGTH - 47 DIA. - 3.7 MM - DRILL/MISC
T="3.7 DRILL"
M6
G0 G17 G54 G90 G94
M3 S548 F92.88
G17 G00 X-21.589 Y-16.407 Z5.
MCALL CYCLE83( 5, 5, 0, -7.362, 12.362, 3, 2, 0,, 1, 1, 0 )
X-21.589 Y-16.407
Y16.593
MCALL
M05
G0 G90 G53 D0 Z0
M30

183307077 发表于 2013-8-6 20:31:19

能用吗！！！！！！！！！！！！！

lexa345 发表于 2013-8-6 20:33:45

本帖最后由 lexa345 于 2013-8-6 20:48 编辑

Drill cycles

1. (CYCLE81/82) Drill/Counterbore
2. (CYCLE83) Deep hole drilling
3. (CYCLE83) Chip Break
4. (CYCLE84) Rigid tapping
5. (CYCLE85) Boring 1
6. (CYCLE86) Boring 2
7. (CYCLE87) Boring 3
8. (CYCLE88) Boring 4
9. (CYCLE89) Boring 5

mi 1-6

1.1=G54 2=G55 3=G56 4=G57
2.1=G154 2=G155 3=G156 4=G157
3.1=G254 2=G255 3=G256 4=G257
4.1=G354 2=G355 3=G356 4=G357
5.1=G454 2=G455 3=G456 4=G457
6.1=G554 2=G555 3=G556 4=G557

183307077 发表于 2013-8-6 20:50:35

我还没有下载就被扣钱啦！怎么回事

1196095169 发表于 2013-8-7 00:43:03

谢谢分享支持一下。。。。

lexa345 发表于 2013-8-7 19:55:05

MasterCam X6

vinney777 发表于 2013-8-7 20:38:19

楼主你的CYCLE83好像是错的哦

lexa345 发表于 2013-8-7 23:03:53

checked DMG 63V

queede 发表于 2013-8-8 23:59:31

是mastercam x6的吗？

sityjw 发表于 2013-8-9 11:10:04

下了怎么用啊大神讲解下 详细点 学个mastercam已经够烦了 没想到后处理水也这么深
页: [1] 2 3 4 5 6 7
查看完整版本: Siemens 840D - 3 AXIS VMC MILL FOR X6