|
|
发表于 2011-8-14 00:03:41
|
显示全部楼层
回复 9# liujianyuhuayan
~0 W k& c7 Y _9 x1 X$ p. w
9 m$ r; @/ E9 w( I. A! F5 s" i5 T6 h& C- J- k1 `
打开后处理,查找
" S. ^. o* ?8 ]. ~$ M1 `/ \( hptoolcomment #Comment for tool0 s% P$ D, d2 m5 W
tnote = abs(t)" L8 m1 @ g9 I2 j' W
toffnote = tloffno; M0 I5 i5 b0 ]+ P- ] V- b
strtool = ucase(strtool); X8 F" h6 l" E
stinsert2 = ucase(stinsert2)4 @5 L3 a! Y, V5 y5 U
!spaces* A3 O: q" C3 H& ?% `
spaces = zero, U0 G) W: e' K/ Z& _& |% p
"(", *tnote, *toffnote, ")", e
* K3 G$ h6 z! s: j) l! A8 P if posttype = two, # Lathe toolpath operation
6 |) j8 w9 s5 y1 K6 s [; e$ z: L* d- ^( b- r
if tool_op = 64, # Drill operation
2 r% o2 H, @( Z) o. y "(", *strtool, ")", e" I7 Z3 i1 _& m: T P- Y
else,6 f/ r( y0 [7 G( U
"(", *strtool, " ", *stinsert, *stinsert2, ")", e( V! }9 L. a2 R& v3 D4 @6 ?0 s+ ]
]2 Z- [3 s) W+ m: o. j1 {) h
else, # Mill toolpath operation
4 E4 A/ e7 i' r3 T$ z) e "(", *strtool, ")", e5 p5 N" L' H& a! l3 E4 T
spaces = prv_spaces7 ^) G7 l) t' N0 ]& V7 t/ W' o/ K
o* @9 C1 R. O/ M j& X9 x) w改为
3 u& U) Z5 X6 F& ~ R7 Vptoolcomment #Comment for tool
( F' N9 f/ c+ p( V tnote = abs(t)
; \3 q7 @9 b9 q, O6 g; b toffnote = tloffno
0 P& r3 Z0 g7 z; k. L strtool = ucase(strtool)8 @5 v* z) ]1 I8 T
stinsert2 = ucase(stinsert2)
% S& m8 E* W5 h5 G& Z. A: L! X0 g !spaces D6 W2 p: F6 p: B+ D
spaces = zero
9 `4 _2 f0 D4 g: b1 Q- o #"(", *tnote, *toffnote, ")", e
# n1 z5 H5 F. ]3 O # if posttype = two, # Lathe toolpath operation
9 X9 y ^1 x, b9 ] S: q: b # [
. L9 ?' q7 n5 w5 Z0 @ # if tool_op = 64, # Drill operation( j* Y, C- @# O7 ?& C: R7 w0 ]+ }8 X
# "(", *strtool, ")", e
$ H" L' z: w9 P7 E3 H- i) \. Z # else,. v! L7 {4 X3 U
# "(", *strtool, " ", *stinsert, *stinsert2, ")", e4 u T+ I5 p3 D5 `$ F3 I, t
#] g. s. h5 R( Z- A
#else, # Mill toolpath operation
$ g( ]3 P# N3 \' G3 K # "(", *strtool, ")", e h8 e2 l$ g. @* h$ D* R& T
spaces = prv_spaces |
|