|
|
发表于 2012-2-20 16:47:21
|
显示全部楼层
回复 9# tangyijuncad
8 [* ?' D$ ~ G1 @, I2 ] H# m7 n: [
; n5 M0 O6 @- v9 z& T6 _0 X方法1:! l+ y3 M6 {5 K5 z1 c
查找
# y3 m( ?8 }# y& sfs2 17 0.2d 0.1d #Decimal, absolute, 2/1 place: @6 J0 w% \8 t" S- s
fs2 18 0.4l 0.3l #Decimal, absolute, 4/3 place
1 F7 n/ C( y( w5 B# p* Pfs2 19 0.5d 0.4d #Decimal, absolute, 5/4 place" o, n$ I8 ]6 u' y% |% j V
& P; Q/ |* n& h) E+ r4 p! a( P+ t
8 Y8 @3 W: C- b, O$ V( T( f5 S- Ifs2 17 0.2l 0.1l #Decimal, absolute, 2/1 place! L9 E ]8 {- s7 m
fs2 18 0.4l 0.3l #Decimal, absolute, 4/3 place% r P2 M* E- ]. {
fs2 19 0.5l 0.4l #Decimal, absolute, 5/4 place! w! y! x' W$ x9 ^" |; ]
7 O' u4 D1 S, r9 m方法2:
% }+ `4 D" h; z e" A( g7 x查找$ U* g a+ Z& K% |; n/ I
fs2 18 0.4 0.3 #Decimal, absolute, 4/3 place2 j2 D2 P6 N$ o* U4 f
改为
, G' a% _% h5 Ofs2 18 0.4l 0.3l #Decimal, absolute, 4/3 place
5 v% Y9 V* M* z& E( D. V
: B- N) o1 }& T$ O/ \9 `9 r; ?查找
( F2 t- z2 R B: `8 J" ipfr_m #Format feedrate for mill& B5 _+ E6 G* |/ s
result = nwadrs(strf, feed)
p* O& p7 V5 I: b result = newfs (18, feed)
8 v, U$ ]/ B. f
. c' o! {+ t. ?' K& Cpfr_l #Format feedrate for lathe2 \( R. {: e, d. J4 H
if opcode$ = 104,
; V1 u$ x, e2 G [
" F9 u, z% j, i! u! ] #Format feedrate for lathe thread
8 D c+ R/ n( e- \) z result = nwadrs(stre, feed)
3 ^; `$ x; b0 z, K" ~4 O result = newfs (18, feed); U4 _; Q0 _. [8 c9 F" @
]
4 V9 w# s3 X) B9 c* u# { else,' d' ]: I% w2 @/ \4 X
[
9 q: e4 }/ y2 q% l9 C8 Q; J0 L result = nwadrs(strf, feed)
" S, ?9 r+ J3 {! O! A8 o result = newfs (18, feed)1 d* [$ w1 {5 ?. }
] |
|