3.3.2：增加预留量输出实例代码

若枫

3.3.2：增加预留量输出实例代码
) H8 S3 X  W. ]+ V
7 }5 }! o2 _- |0 f# x! V7 H: Gmastercam v9.1代码
fmt "XY STOCK TO LEAVE - " 2  xy_stock #Note format
* s# x+ @* W& O* ^fmt "Z STOCK TO LEAVE - "  2  z_stock  #Note format

' t* F' B/ Q* M4 K# _+ L) @pwrttparam     #Pre-read parameter data
) A! g# |9 o4 u4 P+ `      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
      if prmcode = 10068, z_stock = rpar(sparameter, 1)

pparameter     #Read operation parameters
      if prmcode = 10010, xy_stock = rpar(sparameter, 1)
6 ~8 Y4 D- v+ {, n4 ^. ]5 h, i0 h9 Z& v      if prmcode = 10068, z_stock = rpar(sparameter, 1)

/ h0 |; N. O, C在换刀前面加入以下代码
' P4 W0 |; P+ G2 y, H5 T
* r0 Q4 P. m0 i: M1 s& |' S3 Jif xy_stock = 0 & z_stock = 0
if xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e
& \; K2 T; F6 S7 C/ vif xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e  
! H. c' [: ^$ O2 s% ]# qif xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e
7 {7 O( k) L5 x- d5 u
mastercam X5代码
) v  L  r2 w6 qfmt "XY STOCK - " 2  xy_stock #Note format
9 s+ \6 ^0 u' E& Hfmt "Z STOC - "  2  z_stock  #Note format
  _. ~) J! u1 k
1 w% @$ q1 ^0 {  j2 spwrttparam$     #Pre-read parameter data
      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)
# _2 f$ e% J! I" W$ r7 O
pparameter$     #Read operation parameters
. U) r) R' J: D+ }' ^      if prmcode$ = 10010, xy_stock = rpar(sparameter$, 1)
      if prmcode$ = 10068, z_stock = rpar(sparameter$, 1)

4 |$ j9 \" k; M( Y; U% }
3 u. q6 B2 D$ Z  p0 V在换刀前面加入以下代码
1 D$ m: F( A# S6 `$ X5 i$ J6 ]
0 S" Z( e! @8 @8 c6 q0 G! q0 r2 Cif xy_stock = 0 & z_stock = 0
4 d; r, D3 J2 c( C) W6 N, Nif xy_stock <> 0 & z_stock = 0, "(", xy_stock, ")", e$
9 Y* q' l" p3 o+ I. O/ F/ W- a6 ?if xy_stock = 0 & z_stock <> 0, "(", z_stock, ")", e$  
if xy_stock <> 0 & z_stock <> 0, "(", xy_stock, z_stock, ")", e$

2492848737

这些代码添加到个地方呢

ya574544187

学习了 老大 太厉害了