|
|
发表于 2013-6-24 19:17:01
|
显示全部楼层
回复 4# wjm2118
0 `7 y! V$ p/ c4 N+ |( m# _- c/ \1 a. c# n; D5 a6 p/ x
( d( Y e& ?& N 不知你用的是哪个后处理,按照下面的方法修改,mastercam9版适用
4 Y* G. D+ [$ u& z3 t, l
, X& y) s# i: [- k+ b7 S1 O# --------------------------------------------------------------------------
0 M* m4 n' {$ v6 d# Motion NC output
2 ^" B3 P' c4 k4 H" l( I# -------------------------------------------------------------------------- E0 N F* y0 J5 k& X
#The variables for absolute output are xabs, yabs, zabs.
' e0 {! I* Y1 R: S. o5 s#The variables for incremental output are xinc, yinc, zinc.
6 i- X# c" G/ K" X# --------------------------------------------------------------------------
1 ?4 V: v8 r$ R' }/ x5 nprapidout #Output to NC of linear movement - rapid
% X' i9 r5 o4 [, S- n pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, strcantext, scoolant, e$2 I: h! A( A) m4 p8 F$ [2 h& C' q$ L
#Modify following line to customize output for high-speed toolpath) v- z+ c- ]6 Z7 t* _+ \+ z
#tool inspection/change points# M _9 k1 `- C
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
! h- C) t7 Z. g' q5 Y
! V% u( C) O* t, ?2 cplinout #Output to NC of linear movement - feed
+ ?% R3 `+ k" s( F( n pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$
% W" Z# F2 k9 m) R0 S #Modify following line to customize output for high-speed toolpath3 I% a: a$ n. _ g0 X
#tool inspection/change points+ r: L0 ^1 a ^/ V7 X/ ?
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
! _3 {/ e/ v' M- t( u- C- Y# Z6 b( c& L1 s
pcirout #Output to NC of circular interpolation/ w: J, K. j# o- {5 r1 }* k
pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$
/ A8 K+ I+ O. M* P, v! k$ N: Z7 ^# l+ S9 a, U
改为:
8 H7 S$ F& A. X" I. ? C# --------------------------------------------------------------------------
1 x3 A: @# S6 @3 n* F/ J( d" k# Motion NC output! N C( \. q# [! z
# --------------------------------------------------------------------------! X7 W3 U v; `% G- t) H1 t/ E
#The variables for absolute output are xabs, yabs, zabs.
2 E( |) B# o" Y, M7 Y- A#The variables for incremental output are xinc, yinc, zinc.+ m" c, g& M. j2 A7 |
# --------------------------------------------------------------------------! l3 b+ K9 r, W9 l ?- @3 s
prapidout #Output to NC of linear movement - rapid & L& R& ^. H, @, X, W9 W
pcan1, pbld, n$, pccdia,e$" Z% u0 u) z- Q" f! X9 a
pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, 9 k5 O/ ]8 \* L, C8 L D- U
pxout, pyout, pzout, pcout, strcantext, scoolant, e$, Z& L1 ~$ g7 K* F1 s: R
#Modify following line to customize output for high-speed toolpath! R( @5 t5 l/ r& Z9 u* k" b( a
#tool inspection/change points
2 b5 C9 i. y1 `. g8 I( { if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
' Z: e# L3 J* O! F2 q" x
+ t, s& h( `0 d8 e6 q- S& [" V8 Tplinout #Output to NC of linear movement - feed V: b O6 z+ \/ @4 N
pcan1, pbld, n$, pccdia,e$
( m& b7 g) t+ x# ?# F pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc,
3 R2 p( h. t( i) ]4 D8 f7 m pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$
- w2 I3 n' h- M2 j+ Y; K1 }; _ #Modify following line to customize output for high-speed toolpath
6 m& p% s6 M; |6 ] #tool inspection/change points5 J4 ` N$ [1 O, u( z' g
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$2 b3 [/ K1 H! k" f: M$ E
4 E* q" H0 V: u8 A0 apcirout #Output to NC of circular interpolation
4 z* e& p( g9 o/ }* z pcan1, pbld, n$, pccdia,e$3 p' m3 |$ |$ Z. S
pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$ |
|