找回密码
 立即注册

QQ登录

只需一步,快速开始

查看: 21222|回复: 79

[分享] [原创]Mastercam后处理的一些常用功能参数和技巧---2

 火... [复制链接]

67

主题

167

回帖

1万

积分

管理员

积分
13272
发表于 2011-1-11 07:49:53 | 显示全部楼层 |阅读模式

马上注册,结交更多好友,享用更多功能,让你轻松玩转社区

您需要 登录 才可以下载或查看,没有账号?立即注册

×
[p]接上期.

[p]本期主要参数讲解和基本设置,下面进行逐一讲解

[p]<br />' K: C7 x' ?/ \5 I  f4 X* X) k" B
[hidden]arcoutput$&nbsp; &nbsp;: 0&nbsp; &nbsp;&nbsp; &nbsp;#0 = ijk, 1 = r no sign, 2 = r signed neg. over 180 <br />3 P. ~# F: Q' x4 m( A
圆弧输出类型(0=ijk,1=半圆,2=全圆) <br />
: P2 `9 H( {# t8 x' }- Harctype$&nbsp; &nbsp;&nbsp;&nbsp;: 2&nbsp; &nbsp;&nbsp; &nbsp;#arc center 1=abs, 2=st-ctr, 3=ctr-st, 4=unsigned inc. <br />
. |- \5 V1 u5 l! l  U- V输出圆弧的方式(1=绝对值,2=起点相对圆心,3=圆心相对起点,4无方向-增量) <br />
6 r  l1 v) N1 V) B" u) I5 Sdo_full_arc$ : 0&nbsp; &nbsp;&nbsp; &nbsp;#allow full circle output? 0=no, 1=yes <br />) R7 j" I6 k5 x, d4 Z  T: q, J$ O
是否允许输出全圆 <br />
+ C% s; V4 B; v) t; Y8 d* Bhelix_arc$&nbsp; &nbsp;: 1&nbsp; &nbsp;&nbsp; &nbsp;#support helix arc output, 0=no, 1=all planes, 2=xy plane only <br />
/ h: w- i+ v+ ]' D+ L是否支持螺旋输出 <br />; Y9 [* w0 M' D
arccheck$&nbsp; &nbsp; : 1&nbsp; &nbsp;&nbsp; &nbsp;#check for small arcs, convert to linear <br />
+ x/ ^' f$ t" h$ W0 L9 v圆弧检测(当圆弧小于最小设置时,转化为直线) <br />" ~+ b. n- s9 ?8 a& B# f
atol$&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; &nbsp;: 0.01&nbsp; &nbsp;#angularity tolerance for arccheck = 2 <br />9 j5 E2 g5 H1 ~5 l% ?; Z5 z" c
角度公差 <br />
0 D% _" h7 ?" r) Bltol$&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; &nbsp;: 0.002&nbsp;&nbsp;#length tolerance for arccheck = 1 <br />
1 M6 U8 j5 V& O& g长度公差 <br />, v+ y1 a2 Z! ?. Q! p; i
vtol$&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; &nbsp;: 0.0001 #system tolerance <br />4 {" U' s' _) F. n  S
系统公差(英制) <br />9 l: J7 S; ^4 N2 o  V; j0 f# L) O
maxfeedpm&nbsp; &nbsp; : 1181&nbsp; &nbsp;#limit for feed in inch/min <br />) E7 G7 X% B* F
最大进给(英制) <br />5 a6 t+ D& f5 r% r; @- R
ltol_m&nbsp; &nbsp; &nbsp; &nbsp;&nbsp;&nbsp;: 0.05&nbsp; &nbsp;#length tolerance for arccheck = 1, metric <br />" l5 q6 `* u6 i, a/ Z4 e
最小圆弧公差(公制) <br /># |* |6 F9 S+ g
vtol_m&nbsp; &nbsp; &nbsp; &nbsp;&nbsp;&nbsp;: 0.0025 #system tolerance, metric <br />4 R& x, t, _6 i- L7 t
系统公差(公制) <br />. T; A, m, W) n" Z9 d( i) I- [* W
maxfeedpm_m&nbsp;&nbsp;: 30000&nbsp;&nbsp;#limit for feed in mm/min <br />
2 v* g. i! i! A& `最大进给(公制) <br />; U* A. o. Z4 p  i6 `
force_wcs&nbsp; &nbsp; : yes$&nbsp; &nbsp;#force wcs output at every toolchange? <br />3 t( s  p6 F6 k4 y, e: |: ?( s
是否强制输出wcs <br />
3 ]! R) y3 D/ Z# S( j; D/ X" Zforce_dpts&nbsp; &nbsp;: no$&nbsp; &nbsp; #force xy output on all drilling lines including cycle call? <br />
8 u8 S# T/ B0 G+ y是否强制输出相同钻孔点 <br />) e4 }& p4 g" R
spaces$&nbsp; &nbsp;&nbsp; &nbsp;: 0&nbsp; &nbsp;&nbsp; &nbsp;#no. of spaces to add between fields <br />
# _) I4 W4 s9 ~; V是否输出空格 <br />
! q  I% I5 l% V: Komitseq$&nbsp; &nbsp;&nbsp;&nbsp;: no$&nbsp; &nbsp; #omit sequence no. <br />
$ ]0 c7 J- F( X是否输出n号 <br />
- Y6 z! d1 F" i, C- J2 c; Z2 Eseqmax$&nbsp; &nbsp;&nbsp; &nbsp;: 9999&nbsp; &nbsp;#max. sequence no. <br />
" `( o- i4 x9 w/ H6 a" j2 A最大n号 <br />
* P' h( ]1 K" D$ k3 S5 Ouse_gear&nbsp; &nbsp;&nbsp;&nbsp;: 0&nbsp; &nbsp;&nbsp; &nbsp;#output gear selection code, 0=no, 1=yes <br />
! D* P" ~. m6 `- h3 x; V% @) ]3 R% p是否输出用户齿轮代码 <br />1 |0 D, q! J5 D+ `
max_speed&nbsp; &nbsp; : 10000&nbsp;&nbsp;#maximum spindle speed <br />
2 |( F4 ~+ d; B+ h, N: F& [最大转速 <br />& T1 J+ O5 g6 z8 }
min_speed&nbsp; &nbsp; : 20&nbsp; &nbsp;&nbsp;&nbsp;#minimum spindle speed <br />
1 j- P: j9 ~" \9 g5 l( q! z/ E$ N5 c2 }最小转速 <br />
7 a/ A- h9 u  K  f$ G2 lnobrk$&nbsp; &nbsp; &nbsp; &nbsp;&nbsp;&nbsp;: no$&nbsp; &nbsp; #omit breakup of x, y &amp; z rapid moves <br />  l. i  \2 @, E3 o( `
是否分解x,y,z快速进给 <br />
- u# v6 p5 D% @: z/ xprogname$&nbsp; &nbsp; : 1&nbsp; &nbsp;&nbsp; &nbsp;#use uppercase for program name <br />" A3 K; [: O% M. ^) V4 [( D
程序名 <br />
3 I5 r% t' u8 l0 {bldnxtool$&nbsp; &nbsp;:yes$&nbsp; &nbsp; #build next tool table. <br />- \; g& k) V. E! n0 y
是否输出准备刀具 <br />
7 e; O6 N9 U" X* Aarccomp&nbsp; &nbsp;&nbsp; &nbsp;: 0&nbsp; &nbsp;&nbsp; &nbsp;#allow for cutter comp to be applied on arc, 0=no, 1=yes <br />' N: _: F% D  x
是否用许刀补应用于圆弧上[/hidden]

2

主题

89

回帖

151

积分

注册会员

积分
151
发表于 2011-2-25 22:08:13 | 显示全部楼层

re:楼主 真好 这样就能让我们这些菜鸟能自己...

[p]楼主 真好 这样就能让我们这些菜鸟能自己修改自己想要的后处理了~感谢楼主~

Keep Moving
回复

使用道具 举报

1

主题

22

回帖

51

积分

注册会员

积分
51
发表于 2011-4-5 14:07:47 | 显示全部楼层

re:值得學習的內容…用心研讀

[p]值得寃習的內容…用心研讀

回复

使用道具 举报

1

主题

80

回帖

1049

积分

实习版主

积分
1049
发表于 2011-4-9 11:39:32 | 显示全部楼层

re:看看最常用的。

看看最常用的。
回复

使用道具 举报

0

主题

45

回帖

384

积分

中级会员

积分
384
发表于 2011-4-12 17:45:09 | 显示全部楼层

re:偶不会,所以想看看

偶不会,所以想看看
回复

使用道具 举报

2

主题

88

回帖

356

积分

中级会员

积分
356
发表于 2011-6-19 03:07:58 | 显示全部楼层
看看最常用的。
回复

使用道具 举报

2

主题

107

回帖

2027

积分

金牌会员

积分
2027
QQ
发表于 2011-6-22 14:01:45 | 显示全部楼层
一通百通# G$ q9 @/ \) e& A  j/ j; N- `6 V
回复

使用道具 举报

2

主题

81

回帖

113

积分

注册会员

积分
113
QQ
发表于 2011-7-2 22:08:46 | 显示全部楼层
多讲一点就好了。。。以前没有接触到这些
回复

使用道具 举报

438

主题

5759

回帖

901万

积分

管理员

积分
9014290
发表于 2011-7-3 06:51:10 | 显示全部楼层
多来学习就可以.多问就可以了
回复

使用道具 举报

0

主题

3

回帖

7

积分

新手上路

积分
7
发表于 2011-7-11 09:57:10 | 显示全部楼层
很好的资料,学习学习哈
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

站长推荐上一条 /2 下一条

QQ|Archiver|手机版|小黑屋|若枫后处理论坛 ( 苏ICP备11015087号-1|苏公网安备32059002001368号 )

GMT+8, 2026-11-20 03:31 , Processed in 0.206965 second(s), 25 queries .

Powered by Discuz! X3.5

© 2001-2026 Discuz! Team.

快速回复 返回顶部 返回列表