mprouter。pst 后处理坐标系问题，哪位大佬有空帮忙看看，万分感激

75921872

6666.。。。。。。。。。

qq4179351

大佬们现在程序是这样的，中间夹杂很多坐标
+ ?3 v0 L" w% `( o' ~- mG0 G90 G55 X-892. Y-100.
S1800 M3
G43 H6 Z-52.
% m: ~! d) d) w1 f/ VY-5.
& S8 x6 U; H2 O7 K7 dG1 Y-2. F600.
' ?- c8 q8 f5 v5 P% M7 G+ UG2 I12. K0. F3000.
* [- h" A' j/ ]2 eG1 G55 Y-1. F600.
1 y6 b. d; K8 rG2 I12. K0. F3000.
G1 G55 Y0. F600.
G2 I12. K0. F3000.
G1 G55 Y1. F600.
: `' z0 ^1 l9 H6 Y8 \& |G2 I12. K0. F3000.
G1 G55 Y2. F600.
) t; m- O2 c+ p' h2 }G2 I12. K0. F3000.
# C& D& x0 F4 XG1 G55 Y3. F600.
9 b% t. b6 p; t; Q% D. S/ v% IG2 I12. K0. F3000.
G1 G55 Y4. F600.
G2 I12. K0. F3000.
5 L. j4 w$ p) l: m8 F+ Q0 qG1 G55 Y5. F600.
  j; _; C/ |0 m' z& ~G2 I12. K0. F3000.

qq58452077

" z& z1 P- @9 U& F3 V2 F. Y2 Q& W) Q
7 A! T  D% v  j我也发现这个问题
" q+ n0 o- f7 [7 l- Z% j6 T就比较硬核暴力一些
pindex
% f( @; m4 B4 s4 D: s! p      if use_rot_lock & (cuttype <> zero | (index = zero & prv_cabs <> fmtrnd(cabs))), prot_unlock
      pcan1, pbld, n$, *sgcode, *sgabsinc, "G54", pwcs, pfxout, pfyout, pfcout, strcantext, *speed, *spindle, e$
* i4 f& T' n! n8 P# R
6 F: R( n% M) u% ~0 I


0 x! P' ~: p" K! x$ G或者删除PWCS
7 f+ }4 C5 h. ]8 W
plinout         #Output to NC of linear movement - feed
      pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc, pwcs, pccdia,
) n. w: z1 e  M' l2 a        pxout, pyout, pzout, pcout, feed, strcantext, pscool, e$
# r. S  P  D6 Y- t1 w, c1 g$ n      #Modify following line to customize output for high-speed toolpath
  ^' L0 f+ ^* [8 k% i      #tool inspection/change points
      if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$

0 F$ V) ~, {' s) m; d3 T# h
0 e7 s/ Z8 a+ A' jpcirout         #Output to NC of circular interpolation
      pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pwcs, pccdia,
) d" q" V. ^, ^" x# D' s! y0 g# K" E. H        pxout, pyout, pzout, pcout, parc, feed, strcantext, pscool, e$

1 G7 A7 D: l- C2 a! b! A0 X1 _! z

Shujian

( Y' j. |- o$ g6 B) m% Z

若枫 发表于 2021-8-16 19:23
0 a6 K% L/ T; f' I7 z; L( {查找
force_wcs ：yes$
7 G" S3 u& {6 y. y+ e6 u/ U! i改为

，后处理修改总归要懂一点，但是类似的参考文件太少，核心的基本没有，这是MC后处理最大的弊端。