|
|
发表于 2013-6-24 19:17:01
|
显示全部楼层
回复 4# wjm2118
" K! W2 G, @1 S0 B* W) M: x; D2 g+ A7 P/ r
( s1 Q) r# ~" l. y) l+ l 不知你用的是哪个后处理,按照下面的方法修改,mastercam9版适用
# }7 |$ O5 H# M h8 u2 A/ q- _1 j g" e
# --------------------------------------------------------------------------
+ t" g2 \! X( [" F" I# Motion NC output4 V+ V. R* _5 Y0 q. e; q7 |
# --------------------------------------------------------------------------
# ]6 G v3 z! ^5 K: F" k#The variables for absolute output are xabs, yabs, zabs.& x% E4 i8 i- q$ u
#The variables for incremental output are xinc, yinc, zinc.- F, S% S' w$ J1 _7 e
# --------------------------------------------------------------------------
0 \7 k ^& y% Jprapidout #Output to NC of linear movement - rapid
- s/ D: Y# F! n! M" U* o1 O pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, strcantext, scoolant, e$
K9 _% L+ r2 `3 b+ P #Modify following line to customize output for high-speed toolpath$ _0 U, L: F6 m, z v. E" h# x/ t
#tool inspection/change points
! ~3 M) e. h+ b: ^* H; h1 P9 ] if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
: u1 b9 I* T. p- R& F5 Q8 l1 P1 U: M) v% S% l8 `+ h
plinout #Output to NC of linear movement - feed - C* q( b; u* b! t# w2 n1 F P
pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$2 }) |1 V% K- d: \1 M( ?5 N
#Modify following line to customize output for high-speed toolpath3 E) y; ?" Y# U1 V; d8 O: Q
#tool inspection/change points, ?7 \2 w$ j* V4 J4 r
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$0 o- Y$ k" t+ [0 f5 r; I
$ m, w) {8 W! x. w7 X# {* `pcirout #Output to NC of circular interpolation3 _5 ~/ X( e) y6 n$ i5 s
pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$* R. j" C* ]) }6 g( r, G
* X0 V2 \/ P0 v* G% o* D) H+ d( x
改为:; n- P& V& P2 r4 m4 T
# --------------------------------------------------------------------------
7 k9 C1 G/ |" K! s/ t# Motion NC output
7 A3 l8 }% ^3 x6 `! w; u# -------------------------------------------------------------------------- w- o/ ?! V& }3 W$ }( d; M9 t
#The variables for absolute output are xabs, yabs, zabs.
$ ~# n r* b) H* P, K& k( D" }#The variables for incremental output are xinc, yinc, zinc., E. [6 C- X7 { {$ @% h: {: F2 a! B
# --------------------------------------------------------------------------
$ t3 A( n/ s% u& l+ iprapidout #Output to NC of linear movement - rapid " |( H0 h8 |0 j5 a) `# g
pcan1, pbld, n$, pccdia,e$/ |: J# s2 d1 f
pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, 0 F3 p8 S" K3 V% E4 [0 |. F9 |
pxout, pyout, pzout, pcout, strcantext, scoolant, e$4 I3 g# y& |. `2 e4 z
#Modify following line to customize output for high-speed toolpath
c& v6 [+ s. a. f #tool inspection/change points
' \7 r9 g2 {9 |4 ~ if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$5 G$ l2 Z( E$ U9 B- w N
3 U# K% Q. {8 `' k" e" k. u& Cplinout #Output to NC of linear movement - feed $ N+ x1 N" |8 ~% u9 W
pcan1, pbld, n$, pccdia,e$ 1 x! k, L6 C8 R" B: Z# ?
pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc,
% D: z" B/ y( R3 j. a, E1 ^8 @ pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$
+ E& v: w8 ^/ s8 M #Modify following line to customize output for high-speed toolpath- `4 K3 x# \* h7 [
#tool inspection/change points
" n; F" D, B4 u, c1 r; u+ v5 W* q if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
% k$ |0 C5 H1 \7 s- \
4 s) z! ~& y5 m, c3 ]8 l6 U o" O1 @pcirout #Output to NC of circular interpolation
2 h% {+ y8 q3 k+ X pcan1, pbld, n$, pccdia,e$
* | F& g" S, s/ { pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$ |
|