|
|
发表于 2013-6-24 19:17:01
|
显示全部楼层
回复 4# wjm2118 % R d. Q/ m7 @! A! L1 `
' A# m3 K2 n1 o8 {( W- | V9 Y* ^5 J3 c# S/ L( n
不知你用的是哪个后处理,按照下面的方法修改,mastercam9版适用
! w: t+ ~5 x! ^9 u5 ^0 o; A* m& X8 h6 P
# --------------------------------------------------------------------------7 s6 ^8 |* a; m* q& h% X% n
# Motion NC output
& f3 m5 T! S& e4 M6 V6 Z4 G# --------------------------------------------------------------------------
! j% A: V" J0 s, s6 s#The variables for absolute output are xabs, yabs, zabs.- }3 e/ n$ e- V x$ S" J
#The variables for incremental output are xinc, yinc, zinc.
X% _! H' r p9 B( y ^# --------------------------------------------------------------------------
& u4 L6 h, N) U. d4 I# vprapidout #Output to NC of linear movement - rapid * F3 ~5 x& L9 k
pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, strcantext, scoolant, e$3 q$ t% S9 |/ e% Q7 u2 }
#Modify following line to customize output for high-speed toolpath% k- D; i3 A3 |1 s! W0 ^/ F
#tool inspection/change points; _% S- V+ O9 `# |0 x6 T; H" ^0 {
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
5 L' U, Q. l# t9 ~5 m, g6 H! P& W' e9 r w
plinout #Output to NC of linear movement - feed
2 O: ^; S& c* ~9 _: K' x pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$1 d$ t# T# F9 q9 \, r" n: H
#Modify following line to customize output for high-speed toolpath" X; x0 |, v; v/ }5 d$ D! _" v9 B
#tool inspection/change points% J) E! Y5 x$ U- ^2 Y
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
& s3 c; E% @! z5 C. `/ B8 D
& M0 U' ?+ _% E; spcirout #Output to NC of circular interpolation
$ o, ?7 ?1 s* ^2 `/ `9 z pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$
9 K1 W# }( ^3 [. C# F7 q+ B; H4 r8 e- L' j9 h9 ]" A
改为:
# D" G+ u! ?+ y. d2 P# --------------------------------------------------------------------------
7 N% C1 o* Q4 ~4 n+ P# Motion NC output9 I( a; @6 N2 a; s; L
# --------------------------------------------------------------------------# Q) u$ p4 C: J8 I$ o7 V
#The variables for absolute output are xabs, yabs, zabs." [, V! x' T% K: k0 P
#The variables for incremental output are xinc, yinc, zinc.: t) Y8 ?% @! q6 r
# --------------------------------------------------------------------------
5 A# w E' @$ ]' zprapidout #Output to NC of linear movement - rapid 1 k6 ~1 r5 F# v
pcan1, pbld, n$, pccdia,e$6 s3 K6 O/ S, p, `. C1 \" B
pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, 7 e. e- A) n9 ]* [" J7 G
pxout, pyout, pzout, pcout, strcantext, scoolant, e$
* @3 x/ w' D& f& t3 N #Modify following line to customize output for high-speed toolpath% M; T4 F3 X* {. N0 B* A
#tool inspection/change points ~4 _9 ~: @( C& R% b( b/ F; N; t
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
7 l8 Q8 l5 R, q. _
: g7 U# U( p2 R1 Zplinout #Output to NC of linear movement - feed " B3 r J0 e) d* i% K
pcan1, pbld, n$, pccdia,e$
) b- l, L" v0 `( [( k pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc,
4 l9 c- A( R0 ]2 O2 o" a pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$: J" t7 f3 ~" p& A! V$ ?1 J
#Modify following line to customize output for high-speed toolpath
- S! k, C9 {, ? N! ?, i( O g #tool inspection/change points
! Z5 i/ I, B/ p) ]# l4 b if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$2 Y! O( R1 ~% D& C
) @- f9 N0 @' Z( A; E6 o. O
pcirout #Output to NC of circular interpolation
; Y& W+ j$ u/ H- i$ d pcan1, pbld, n$, pccdia,e$
]! o5 U! }" @# T2 t pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$ |
|