|
|
发表于 2011-8-14 00:03:41
|
显示全部楼层
回复 9# liujianyuhuayan
0 F9 R& G4 @$ ^; g8 N- t E4 x* @( R0 G8 ^. f4 z
* [9 u% h) q# J: Z4 B
打开后处理,查找
% h5 j8 l4 |9 D" a6 m; _" A2 A0 sptoolcomment #Comment for tool
4 _/ z0 {& {$ [& I/ c2 `9 e3 e [ tnote = abs(t)
) h; w; e6 g5 H: h E5 F9 ^ toffnote = tloffno
6 @. G3 X7 y4 @1 ~2 X, L3 h strtool = ucase(strtool)
9 o! d. {" b; p& g; ^ stinsert2 = ucase(stinsert2)
8 v! ]) c0 x; i3 c% m6 @* v !spaces
& N7 O; i, _: M8 `4 @ spaces = zero1 P. b2 B/ q" U! j5 M
"(", *tnote, *toffnote, ")", e
) {5 r& y6 g" y0 Q% D! x if posttype = two, # Lathe toolpath operation0 B3 Q; T8 W7 G& b' M! s
[
J8 C, L' w! w0 P$ K0 `6 V0 \ if tool_op = 64, # Drill operation5 o3 t+ Y) _- e+ u1 {% t
"(", *strtool, ")", e8 [9 F; u3 C* A( c- y5 ~* @) M# E
else,
% {3 S* A. d" N: D "(", *strtool, " ", *stinsert, *stinsert2, ")", e
7 |$ f/ q) }( N7 X2 ]# ` ]7 e4 w8 B ^$ L6 X
else, # Mill toolpath operation
4 \# [' w) k$ d! h1 q/ ]4 m6 | "(", *strtool, ")", e7 c7 @& m7 [' w0 n6 [$ d5 m
spaces = prv_spaces7 { f. w1 O8 R
2 M& x; N( i& G, w改为
% ^2 e) m! u! b6 vptoolcomment #Comment for tool
6 c {- }/ [2 _7 R; v( u tnote = abs(t)
L; Y. J% N0 { toffnote = tloffno
3 k8 ]4 ]* N# g a0 `/ ~) _2 C1 I strtool = ucase(strtool)
3 R" H) c3 T. I. F stinsert2 = ucase(stinsert2)( R- |4 G9 n( Y
!spaces4 |+ ^, o' \; ~ R. l' J
spaces = zero
2 W; ~5 d: u6 w H #"(", *tnote, *toffnote, ")", e4 K6 J: f) t/ v5 Y
# if posttype = two, # Lathe toolpath operation9 [- \2 r. u6 v3 u3 e5 H
# [
+ U" @. R% b/ c; _# Z/ l # if tool_op = 64, # Drill operation: D3 k/ U P3 {8 L6 z
# "(", *strtool, ")", e
& m [6 @7 V) ~6 ?/ P+ M # else,9 }) E# l3 J: o& i& x
# "(", *strtool, " ", *stinsert, *stinsert2, ")", e e; ^, [# N9 C+ F
#]+ G/ E( c) P% x
#else, # Mill toolpath operation
* p4 r0 x2 r) k! B7 p& F. M" @ # "(", *strtool, ")", e8 F7 Z* {. f: z- L) |# z
spaces = prv_spaces |
|