|
|
发表于 2012-2-20 16:47:21
|
显示全部楼层
回复 9# tangyijuncad ; Q; i! B. |3 l% N0 l9 ~
8 R8 w% ^, m! {7 G
" |7 U# q8 N5 o. e! o7 y4 E! t
方法1:; ]" r8 o/ A6 K! Q4 [
查找9 ?' H9 l- d( {# J
fs2 17 0.2d 0.1d #Decimal, absolute, 2/1 place
9 W2 q) D+ x2 Efs2 18 0.4l 0.3l #Decimal, absolute, 4/3 place5 ]8 W& J; V: J. P1 V# U8 {
fs2 19 0.5d 0.4d #Decimal, absolute, 5/4 place
. m) m+ O) c1 R s/ e
" a7 J7 U: b1 w: f
# U3 f; }/ {1 h7 |; i/ d8 afs2 17 0.2l 0.1l #Decimal, absolute, 2/1 place0 s2 s$ D* z' j# `; j
fs2 18 0.4l 0.3l #Decimal, absolute, 4/3 place
- m- ^" W+ N( u8 M+ Vfs2 19 0.5l 0.4l #Decimal, absolute, 5/4 place
; B9 F8 p' i! [* k& e& f( B& h r1 s
方法2:! R# n! K: @# A+ n
查找3 X t: L9 ?* J: P" U
fs2 18 0.4 0.3 #Decimal, absolute, 4/3 place
, w% @; ^1 M/ H8 Z! T改为
( H$ L9 S6 ]; B% B, M3 ~! z6 k( Ufs2 18 0.4l 0.3l #Decimal, absolute, 4/3 place
" w2 {+ h$ n, p' V! I b, Q& G; B( U( {' ?1 m1 O5 v
查找% \/ W; C# z q
pfr_m #Format feedrate for mill& ]+ m' l4 T* r* E P
result = nwadrs(strf, feed)" W2 o3 Y2 U9 P& E
result = newfs (18, feed): _' ~" |, E1 e$ i8 S6 Q9 h. }0 t
, v7 W1 S, S( C+ a
pfr_l #Format feedrate for lathe1 U/ [/ @/ X8 X* r4 ~
if opcode$ = 104,' m3 |- @8 } ~7 ^; b. G; p. L( U4 e
[
6 B" u1 q! W1 s: }) Y8 L #Format feedrate for lathe thread5 |$ \+ d6 E* L
result = nwadrs(stre, feed)
5 K7 b3 E$ L+ i9 d* V result = newfs (18, feed)
: r+ g- z: F; n+ | ]
2 g# v8 i/ |- M: N: Y else,, |/ l: c4 {. W. H! [1 y: z' @
[' m; T5 o9 E% P# u& ~' p
result = nwadrs(strf, feed)
9 [* q( c8 p* J' `7 u$ e result = newfs (18, feed)
) e* o) M# S" |9 k# T, `6 S8 S ] |
|