|
|
发表于 2013-6-24 19:17:01
|
显示全部楼层
回复 4# wjm2118
5 d" Z/ m% r' a6 K5 H: m+ m) f! f( }1 ~7 l
$ s4 t5 [3 z& o) E. @# S
不知你用的是哪个后处理,按照下面的方法修改,mastercam9版适用
1 T- P/ {& Y* S1 V
8 z# a9 a# ~& {8 Z4 Y8 X0 D# --------------------------------------------------------------------------# G& j, c( b$ j
# Motion NC output2 p5 t6 Y8 X$ @
# --------------------------------------------------------------------------
6 i, S W) o% \" _#The variables for absolute output are xabs, yabs, zabs.2 Y: }: M+ m! Q
#The variables for incremental output are xinc, yinc, zinc.; ]3 E% c- Q2 ]+ _3 L7 y- a7 [
# --------------------------------------------------------------------------; r& p& J6 G' f/ C0 O1 S. S
prapidout #Output to NC of linear movement - rapid # X6 V6 v, {8 a: H4 ]( ]) H
pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, strcantext, scoolant, e$% D) w$ L/ t% v
#Modify following line to customize output for high-speed toolpath
8 u! |, R( x( V, R n7 _ #tool inspection/change points% T0 j* C$ g0 o n3 q- W7 a
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
% L8 i: R; k8 `, Z# C' T. M- I3 A7 L4 i/ M9 b9 {+ L4 s8 y
plinout #Output to NC of linear movement - feed
+ h3 O# Z8 M0 ]' { pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$
+ ]* f/ U% }6 C+ j2 d) N l #Modify following line to customize output for high-speed toolpath/ Z D6 }; _. d
#tool inspection/change points
7 B. c" M! }6 W& Q7 F1 @$ l if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
4 S8 y( s. i7 y) S0 M4 {* Y3 B0 @( D8 y
P. ?7 T. u4 \) [- Cpcirout #Output to NC of circular interpolation$ |. |% b8 I0 H L& x& H6 v7 R5 Q
pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pccdia, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$% N6 l. B _, v t6 k; c: X; e1 R& V8 n
& B$ e1 ~( n( C0 u4 L
改为:7 [& H0 J$ v; G3 M
# --------------------------------------------------------------------------
7 n9 L e; D- W# Motion NC output) P G7 L/ o: L+ m
# --------------------------------------------------------------------------
p8 ^5 l. o2 o5 q0 g+ I#The variables for absolute output are xabs, yabs, zabs.7 ^2 `: c" u: u4 [& X E
#The variables for incremental output are xinc, yinc, zinc.
" P _6 A3 {1 P4 ~+ x6 [5 x# --------------------------------------------------------------------------
7 A# U8 |' l9 m X% u* Nprapidout #Output to NC of linear movement - rapid 4 A( J7 d3 ^5 {. ^/ l6 C( L
pcan1, pbld, n$, pccdia,e$2 y H. _# W9 B0 a' W8 U
pcan1, pbld, n$, sgplane, `sgcode, sgabsinc, - P: N8 A9 y$ @2 P% _9 P$ O
pxout, pyout, pzout, pcout, strcantext, scoolant, e$
/ M2 h0 k: X. k #Modify following line to customize output for high-speed toolpath
6 F5 P3 z) Y8 B# V #tool inspection/change points8 x$ k o4 s5 }
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
! N1 G- J' X+ V! b u
8 ~' ?4 n s8 O9 c9 Y0 b( E/ Rplinout #Output to NC of linear movement - feed
2 ~3 x9 T- y, A! ?9 b; ?& Y pcan1, pbld, n$, pccdia,e$
2 G4 B! a! v1 W# v pcan1, pbld, n$, sgfeed, sgplane, `sgcode, sgabsinc,
" c9 B" J) ^& p. p8 M$ g z( ~ pxout, pyout, pzout, pcout, feed, strcantext, scoolant, e$
k/ ?* A3 `9 u6 b3 C' @1 {2 j #Modify following line to customize output for high-speed toolpath
5 n$ p, b+ Z% \ {) Z #tool inspection/change points2 ^, j6 g( H1 W, ]3 ? `
if rpd_typ$ = 7, pbld, n$, "M00", "(TOOL INSPECTION POINT - POST CUSTOMIZATION REQUIRED)", e$
T6 \# a4 _, S, K, f
& h5 j5 A6 p' f8 w) I3 xpcirout #Output to NC of circular interpolation
, z, C1 F5 f* s pcan1, pbld, n$, pccdia,e$
4 s7 [. m; z- |9 B( ]3 }3 i6 i pcan1, pbld, n$, `sgfeed, sgplane, sgcode, sgabsinc, pxout, pyout, pzout, pcout, parc, feed, strcantext, scoolant, e$ |
|