|
|
楼主 |
发表于 2015-12-25 10:33:48
|
显示全部楼层
回复 2# 若枫
) G) L/ } @8 L8 p, I. d/ {3 t6 k8 T1 i- n2 ^2 K
5 c# G; |/ R9 @' p. w/ ]
老大:2 E( H2 P( @) t$ F
感谢您的回复!以下是我的方法,这样的确出来两个G代码。
/ P, m! x2 S1 M. a/ D
5 c+ g/ R: X# k9 n& m& R
% C* K3 ~7 c2 l9 } if drillcyc$ = 9,
6 D8 X7 ^$ q9 C+ {! R+ w8 I( ~3 H [3 c" p& l7 j2 Q& a5 }
pdrlcommonb$ ]! ?- l1 |" `1 y- g8 V% }$ K4 |
peck1st =peck1$
, h1 V, D) i( n! L1 ^2 a4 { if dwell$ = 0,pcan1, pbld, n$, *sgdrlref, "G1181", pxout, pyout, pfzout,- ?1 F$ R6 a0 ~) ]$ K
prdrlout, dwell$, *peck1st, *peck2$, *feed, strcantext, e$( }4 _' R3 T$ j; E) ~; f
else, pcan1, pbld, n$, *sgdrlref, "G1182", pxout, pyout, pfzout,! o/ Y% E; B1 V Z; M R8 |
prdrlout, dwell$, *peck1st, *peck2$, *feed, strcantext, e$
; M( c* _7 {* O" q pcom_movea, c: [# T* R5 @! }: z
]: _1 K- P% |+ P w5 }# W6 `
, d! x M& h+ s% R! l. ]. L) S但使用以下的方法出不来一个钻孔循环两个不同的G代码。上面的"G1181”用原来的*sgdrill出来的是G81
, A {; d3 v* h9 ~3 R8 w! ?sg85 : "G85" #bore #1 - no dwell
1 ? o7 `8 e' T% gsg85d : "G89" #bore #1 - with dwell
$ N0 h5 g7 u4 }6 v4 s6 |2 S" Rsg86 : "G86" #bore #2 - no dwell
# a) {2 r N) w) ksg86d : "G86" #bore #2 - with dwell
* Q6 T) I1 ?# Y+ z4 ]sgm1 : "G76" #fine bore - no dwell! l: j P. E6 ~
sgm1d : "G87" #fine bore - with dwell
# U% Q. P: t+ c- ]- |$ Y& fsgm2 : "G84" #rigid tap - right hand3 D/ i- L1 H, Z( x, Q4 q3 n
sgm2d : "G74" #rigid tap - left hand
4 |3 J: Z* b' W6 Hsgc9 : "G183" #custom #9 - no dwell2 S5 b9 K; ?$ h1 X, L0 Y
sgc9d : "G184" #custom #9 - with dwell: b5 ?/ @3 w, C5 g5 u3 w3 d
sgc10 : "G185" #custom #10 - no dwell
' ]: d2 A2 Z% }6 A6 Z* ]$ ?sgc10d : "G186" #custom #10 - with dwell
9 ?8 F: o# h3 r4 _- B$ |7 ?& M. R. g1 t$ f7 k1 B/ r' `
9 J# y l8 N* c9 ?! _' w$ a' F
请指点一二,谢谢!
$ E9 z* w" p; ~最终我要出25个左右钻孔循环,30多个G代码。 |
|